Maytag washer F9 E1 is one code, not two. Maytag’s support pages call it a long drain time, which means the washer couldn’t empty the tub when it expected to.
Most of the fixes cost you nothing. You check the drain hose, clean the pump filter if your model has one, and clear the drain the hose empties into. If the code comes back after that, you’re looking at a service call.
What does F9 E1 mean on a Maytag washer?
F9 E1, often printed F9E1, is Maytag’s long-drain code. Maytag says the washer is unable to drain correctly, and its front-load page lists three places to look: the drain hose installation, the drain pump filter and the door seal. The same code appears on top-loaders.
The display splits it into F9 and E1, so you’d be forgiven for hunting two faults. It’s one. A replier in an r/Appliances thread put it plainly:
“Those arent separate errors thats one error. F9e1. Thats how most all whirlpool product errors are formatted especially washers. I dont have the service manual or tech sheet for that. Buy off the top of my head im 75% sure f9e1 is long drain. Dont take my wor…” [excerpt, 320 characters in full]
– r/Appliances (3 upvotes)
The replier was working from memory, and Maytag’s pages confirm the reading. If you own a Centennial, our Maytag Centennial error code guide lists F9E1 in the same F#E# family as F1E1 and F7E1.
Check the drain hose first: depth, tape and kinks
Start here, because it’s free and Maytag lists it first. You’ll often find a hose pushed too far down the standpipe because it looked neater, and it was a regular find on my service calls.

Front-load washers
Pull the washer out far enough that you can see where the hose enters the drainpipe or laundry tub.
Maytag’s front-load F9 E1 page says the hose shouldn’t go more than 4.5 inches (113 mm) into the drainpipe. Past that, water you’ve already drained can siphon back into the washer.
Look for tape next. Maytag says not to seal the hose into the drainpipe with tape. It should sit loose but secure, with a gap so air can break the suction. Without that gap, water keeps getting pulled out while the tub fills.
Then check the shape. Maytag says the U-shaped form from your installation instructions gives the right length in the drainpipe, and the hose tops out at 96 inches measured from the bottom of the washer.
Top-load washers
The top-load F9E1 page asks for the same things in different words. Your hose shouldn’t sit beyond the elbow in the standpipe, which Maytag says can cause siphoning, water draining back into the tub, or a slow or no spin.
Don’t tape the hose to the drain pipe, and don’t reshape it. The form it ships in is the right one for a standpipe or a wash tub.
Then straighten any kink you find and clear whatever blocks the drainpipe or utility sink. Maytag names both.

Clean the pump filter and the door seal
Front-loaders have two more spots that clog. Maytag says the drain pump filter sits behind the bottom dispenser drawer on some models, and a clogged one stops the washer from draining well.
Not sure your machine has one? Your Owner’s Manual shows where it is. These are Maytag’s steps for a model with a storage drawer, so follow the manual if yours doesn’t have one.
- Unplug the washer.
- Open the storage drawer, then lift it out by releasing the tab on each side. Push down on the right tab and up on the left.
- Put a large, flat container under the filter and a towel beside it.
- Release the black hose from its clip, remove the plug and let the water run into the container.
- Turn the filter counterclockwise to take it out. Pull off the lint by hand and rinse the rest under water.
- Turn the filter back in clockwise as far as it goes, with the handle close to vertical. Replace the plug and secure the hose in its clip.
Then wipe the door seal. Maytag says small drain holes inside the seal can clog and slow the drain. I’d still do the filter before you pick up a screwdriver.
Water still in the tub and the door locked
On a front-loader, drain the tub through the pump filter hose: unplug the washer, set a flat container under the filter, release the black hose and pull its plug. On a top-loader, unplug the washer, pull the drain hose out of the standpipe and lower its end into a bucket on the floor.
Water in the tub is often why the door or lid stays locked. Beacon Appliances, a service company, lists a locked door among the F9E1 symptoms. It says the door can stay locked until the water drains or you cancel the cycle.
Its safety list also tells you to expect spills, so lay towels down before you start.
Is the top-load lid still locked after the tub is empty? Stop there. An appliance tech on JustAnswer, answering a Maytag MVW6230HW owner, said the next step meant removing the console screws and lifting off the top section. That’s a service call for most households.
How do you clear the Maytag washer F9 E1 code once the drain is fixed?
Fix the drain, then run a short drain or spin cycle and watch it. Maytag’s F9E1 pages list no reset sequence, so there’s nothing official for you to enter. The code comes from a slow drain, and it should stop returning once the water leaves the tub on time.
I won’t hand you a button combination, because Maytag doesn’t publish one for this code. A reset can hide the message. It doesn’t change how fast the water leaves.
When the easy checks don’t clear it
Say you’ve done all of it: hose depth, tape, kinks, filter, seal and the drain the hose empties into. One owner posted what happened next.
“We’ve reset the breaker and let it sit for 30 mins and restarted it. We’ve drained the thing and made sure the filter was clear – it was. We did a hard reset on the control panel via a factory code. Does this thing need a new board? Or??! Also, it doesn’t do this right away. In a regular 45 ish cycle- this doesn’t happen until around the 20- something mark. Thanks! Update: thanks for all the tips! With your help I was able to search better than I was before. With the delay in board issues- I’m…” [excerpt, 679 characters in full]
– r/Appliances, June 2026 (5 upvotes)
That owner had cleared the power, drained the tub and found the filter clean, and the fault still showed up mid-cycle. At that point you’re past the free checks and into DIY limits.
Beacon Appliances names the less common causes: an obstruction at the drain pump impeller or a weak pump, wiring to the pump, a pressure-sensing fault on some models, and the main control. It also says F9E1 is more often a restriction, an installation issue or a clogged filter than a bad board, so the board comes last.
On a Bravos MCT top-loader, our Maytag Bravos MCT diagnostic mode guide covers a test cycle that includes the drain pump. You can find other Maytag symptoms on our Maytag washer error codes page.
Stop and call a pro if the pump hums or grinds while the tub stays full, if you see damaged wiring, or if the code returns after every fix above. Beacon’s safety list also says to stop at a burning smell or harsh grinding. I don’t touch pump wiring or a control board on a homeowner’s say-so, and you shouldn’t either.
Frequently asked questions about Maytag F9 E1
Does Maytag washer F9 E1 mean the same on front-load and top-load washers?
Yes. Maytag’s front-load and top-load pages both describe F9E1 as a long drain. The checks differ, since only the front-load page lists the pump filter and the door seal.
Is F9 E1 a bad control board?
Rarely the first suspect. Beacon Appliances says the code is more often a restriction, an installation issue or a clogged filter than a bad board.
How high can the drain hose go?
Maytag’s front-load page puts the maximum hose height at 96 inches, measured from the bottom of the washer.