Skip to content
Bosch dishwasher E22 means a blocked filter, E24 means not draining through the filter, hose or disposal plug, and E25 means the drain pump is blocked or its cover is loose.

Bosch Dishwasher E22: Clean the Filter, Then Check These

Before you begin

Disconnect power and shut off water or gas where applicable. Stop if the repair requires licensed work.

A blocked filter is behind a Bosch dishwasher E22. That’s what Bosch’s own E22 page says, and it names no other cause. Pull the filter, wash it and put it back before you try anything else. You’ll need only mild soap and a soft brush.

If the code stays after that, you’re past the easy part. I’ll cover both, in the order I’d work them on a service call. Most of my calls were Whirlpool-family machines, with fewer Bosch, so I pulled the tech sheet first and touched nothing until the power was off.

What does Bosch dishwasher E22 mean?

E22 is a filter code. Bosch describes the filter as the spot where food particles get caught, and says it needs cleaning regularly. When it clogs, the machine flags it. Have you pulled yours since you bought the machine?

Bosch uses nearby codes for drain trouble, and you can easily mix them up. E24 means the water isn’t leaving. E25 points at the drain pump, which sits under the filter. All three start in the same spot.

Don’t read E22 as a dead pump. On Bosch’s page it’s the mildest of the three, and the fix costs nothing.

How do you clean the filter on a Bosch dishwasher?

Take the filter out and wash it under running water with mild soap and a soft brush. Bosch says the same on its filter-cleaning page, then you reinstall it.

Unplug the dishwasher or switch off its breaker first. Shut off the water supply too, the same routine I followed on every call.

  1. Pull out the lower rack.
  2. Lift out the lower spray arm.
  3. Twist the filter and pull it out together with the mesh screen.
  4. Wash it under running water with mild soap and a soft brush.
  5. Put the filter and spray arm back, then slide the rack in.

Bosch’s filter page says the filter protects the pump from food debris and keeps food from landing back on your dishes. It sits right where the pump starts, so a clog there backs everything up.

Hand lifting the round filter out of the bottom of an open dishwasher tub with the lower rack removed.
Illustration: the filter lifts out of the tub floor once the lower rack is out.

How the filter comes apart differs by model, so check your owner’s manual if yours doesn’t twist out. Once it’s back in, reset the machine. Our Bosch reset guide covers cancelling the cycle versus cutting the power.

Why is E22 still showing after you cleaned the filter?

Usually the filter wasn’t the whole story, or it isn’t seated right. Bosch’s E22 page stops at the filter and tells you to contact support, so what follows is my own order of checks, borrowed from Bosch’s E24 and E25 pages.

Treat these as the cheapest places to look first, not a Bosch procedure, because Bosch lists no second step for E22. One owner on r/appliancerepair described exactly this. They’d had E22 on and off for two years, scrubbed every filter piece until it was spotless, and still saw standing water. Two commenters answered.

“There is supposed to be standing water yes. Run your unit regularly and crack the door open when not in use to help with the smell. Check your drain line going under the sink for blockages”
– r/appliancerepair, February 2026 (2 upvotes)

“Water in the bottom can come from a bad water inlet valve leaking into tub when not in use or a drain pump that is not evacuating the water. Cancel the cycle and see if it drains or look at the port where the water comes in the sidewall and see if water drips out of it constantly..”
– r/appliancerepair, February 2026 (3 upvotes)

Those are forum answers, not Bosch’s word. They do match what I’d check next. A little water at the very bottom can be normal, so look at whether your tub stays full after the cycle.

Check the pump cover under the filter

With the filter out, you can see the drain pump cover. Bosch’s E24 page says to make sure it isn’t loose. Its E25 page has you pry the cover off with a spoon, then clear debris and standing water with a sponge.

Bosch warns that some debris may be sharp, so go slowly. I always wore a headlamp for this part and went slowly.

Check the drain path

If the tub stays wet, follow the water out. Bosch’s E24 page lists a kinked or blocked hose, an unsealed siphon connection under the sink, and a new garbage disposal that still has its knockout plug in.

That plug is the one I’d look for after any disposal swap. Our Bosch E24 guide walks through all of it, and the full Bosch code list covers the rest.

When should you stop and call Bosch?

Stop when the filter is clean, the pump cover is seated, the drain path is clear and E22 still comes back. Bosch’s page sends you to Customer Support at (800) 944-2904 at that point, and so would I.

The next part is the pump or a part you can’t reach from inside the tub, and guessing there gets expensive. If the machine is old, run it through the appliance age calculator before you pay for anything.

E22 is a filter code first. If you’ve cleaned it properly and the code returns, the next stop is the pump area or a service call, not a parts order.