A Whirlpool ice maker not working is usually down to one of four cheap causes: the control arm is up, the freezer is too warm, the water filter is clogged, or the fill tube has frozen. Test them in that order before you buy a part.
Work a Whirlpool ice maker not working problem the way a service tech does: free fixes first, parts second, a technician last. The temperatures, intervals and reset steps come from Whirlpool’s own help pages. The stop signs mark where you should quit and call someone.
Own a Samsung instead? The Samsung ice maker not working after reset page follows that brand’s own reset order.
If you’ve already ruled out the arm and the temperature on any brand, the ice maker not making ice but water works page digs into the water side.
Whirlpool ice maker not working: the two-minute checks
Open the freezer and find your ice maker. Depending on your model, Whirlpool says it sits in the upper freezer, inside a freezer drawer or along the interior freezer wall.
Look for a power switch or a control arm. The arm is the wire or plastic handle that rests on your ice bin. When it’s raised, the maker thinks the bin is full and stops.
Whirlpool’s ice maker troubleshooting page lists a loose, broken or accidentally pushed-up arm as a cause of halted ice production.

Push the arm back to the on position. Tighten it if it’s loose. If it’s snapped, you need a part, and Whirlpool says to contact a professional.
On service calls I looked here first, because the arm often gets nudged when someone reloads the freezer. It costs you nothing, so it goes first.
Next, pull your bin. Whirlpool says ice clumps in the bin or chute can jam the dispenser, and a bin that isn’t seated correctly can make ice miss the bucket.
Break up small clumps by hand. For a big solid block, let the bin thaw fully instead of chipping at it.
Reset it the way Whirlpool describes
Not every Whirlpool maker has a reset button. Whirlpool’s ice maker reset page says some units have one and others only respond to a power cycle. Work through these in order:
- Switch the ice maker’s power switch off, wait a few seconds, then switch it back on.
- Pull the bin and set paper towels under the dispenser. Water or ice can drop during the reset.
- No switch? Unplug your refrigerator, wait about five minutes, and plug it back in.
- If your unit has a reset button, press and hold it for about five seconds with a pencil eraser. Whirlpool puts it on the underside or back panel of the maker.
- Give it time. Whirlpool says production can take up to 24 hours to return, though you may see first cubes within a few hours.
Whirlpool also recommends tossing the first one or two batches after a reset. Don’t judge your fix by the first tray.
A reset clears a stalled cycle. It won’t thaw a frozen fill tube or cool a warm freezer. Still nothing the next day? Move on to the numbers.
Freezer temperature, filter and water pressure
Whirlpool’s targets are 0°F (-18°C) in your freezer and 33 to 40°F (0 to 4°C) in the refrigerator section. A warm freezer slows your ice or stops it.
A freezer that’s too cold causes trouble too. Whirlpool says below -10°F, cubes can freeze so fast on the outside that the maker ejects them hollow in the middle.

Your filter comes next. Whirlpool says to replace it every six months, and a clogged one cuts the water reaching the maker.
Slow water at the dispenser, black specks, or odd-tasting ice all point at the filter.
Then look behind the fridge. Slide it out carefully and make sure the water line isn’t kinked or twisted. Confirm the shutoff valve is fully open.
If your filter is fresh and the line is clear, suspect the water inlet valve. Whirlpool’s help page says a valve fed with less than 20 psi can’t push enough water to the maker, and you should test the pressure first.
At 20 psi or higher, the valve itself may need replacing. Unless you own a pressure gauge, this is the point to bring in a pro.
One more cold-side problem: if your freezer ran too cold, the fill tube behind the maker can freeze shut. Whirlpool says warm air or water will thaw it, but it recommends a professional because the bin and maker have to come out.
Fix the temperature first and give both compartments 24 hours. The thaw may take care of itself.
What the ice in the mold tells you
What’s actually sitting in your maker? Look before you buy anything, because the ice sorts the remaining causes faster than another reset does.
- Empty mold, empty bin: water isn’t arriving. You’re looking at the filter, the line, the inlet valve or a frozen fill tube.
- Small or hollow cubes: Whirlpool ties these to poor water flow or a freezer colder than -10°F.
- Cubes frozen in the mold that never drop: water got there, so your problem is on the eject side. That points toward the heater, the rake or the motor.
- Clumps in the bin or chute: a bin problem. Thaw it and reseat it, as above.
The third case is where owners get stuck. In r/appliancerepair’s “Help with Whirlpool ice maker” post, the top comment came from someone who had already fitted a new maker:
“New icemaker. The heater is no longer dislodging the cubes from the mold.”
– r/appliancerepair, November 2026 (9 upvotes)
Two replies in that post said to replace the maker.
A second post shows how far people go before they stop. A poster with a WRF535SWHZ07 had cycled the power, cycled the stop arm and fitted a new filter. The freezer sat around 0°F, and partial cubes stayed in the maker.
One reply guessed the rake was out of its home position, at the 3 o’clock spot. Another offered this for newer makers:
“Oh that’s the newer model. Much easier to advance the cycle. Simply turn that big gear the same direction it says turn. You may have to tape or hold the door switch close to watch the motor turn. But a certain point it should start turning on its own.”
[excerpt, 340 characters in full] – r/appliancerepair (1 upvote)
Later in the same post, someone turned the gear until it stopped and then couldn’t move it. The poster had also asked which holes were the T and H ports on their maker, since it looked different from the videos they’d found.
Why not just jump the terminals? Forcing a cycle means working at a powered maker with its cover off. Dale, my old boss, made me read the tech sheet before touching a part.
You shouldn’t try a jumper test without the sheet for your exact maker.
Where DIY ends
Stop and call a pro if your fill tube keeps freezing, the control arm is broken, your water pressure reads under 20 psi, or the fix needs the maker pulled while it’s powered.
Unplug your fridge before you pull the bin or the maker.
A freezer that won’t pull down to 0°F is a cooling problem, not an ice maker problem. Refrigerant work isn’t DIY.
Before you buy a replacement maker or a new fridge, enter your model number in the appliance recall lookup. It lists CPSC recalls since 2021, so older notices won’t show up there.
Whirlpool also offers online repair scheduling through its Customer Care pages.
Once your maker is running, clean it. Whirlpool’s reset page suggests every three to six months, and the how to clean an ice maker page covers fridge models.
Whirlpool ice maker questions
Whirlpool ice maker not working but the water dispenser works: why?
A working dispenser only proves water reaches the door. It doesn’t prove water reaches your ice mold, and a raised arm, a frozen fill tube or a warm freezer can stop the maker alone.
How do I force my Whirlpool ice maker to cycle?
The safe way is the reset: power switch off and on, or hold the reset button about five seconds if your unit has one. Gear-turning and jumper tests exist, but they need your model’s tech sheet.
How long until ice shows up after a reset?
Whirlpool says production can take up to 24 hours to return, though first cubes may appear within a few hours. It advises discarding the first one or two batches.
Where is the Whirlpool ice maker on/off switch?
It’s on the ice maker unit in your freezer, which Whirlpool places in the upper freezer, inside a drawer or along the freezer wall. On some models the raised control arm is the off position.